Holland Pump Catalog - Catalog - Page 50
50-31
WELLPOINT PUMP
2026-3
WP12-SS
PUMP SPECIFICATIONS
Size: 12” (300mm) Rotary Wellpoint Pump
Pump: Vogelsang 520Q, Class 30 gray cast iron casing and
smooth end cover
Solids: Handles up to 2.5” compressible soft solids
Rated Capacities: 2656 GPM (355 CFM) @ 500 RPM
Displacement: 531 US gallons per 100 revolutions
Working Pressure: up to 87 psi
Flange Connections: 10” Flat Face ANSI, 150 lbs. Flange
connections included
Rated Speed: 0 - 500 RPM. Consult factory for
recommended operating speeds
Rotors in: Helix three wing rotors, NBR standard, other
materials available on request
Wet-Ends: Standard in Gray Cast Iron
Shaft Material: Alloy Steel, AISI 4140
Rear Door: Contains 2 bearings and two mechanical seals
to prevent shaft deflection. The door is readily removable for
changing lobes, mechanical sea cartridges and wear plate.
Gear Material: AGMA Class 8, SAE 1045
Mechanical Seals: Duronit vs. Duronit cartridge seal
Vibration: Pumps and motors operate at any point
within their operating range without undue noise and
vibration
Top and Bottom Housing Segments: ASTM A48 Class 30
gray cast iron coated with ceramic epoxy for wear resistance;
options include Ryton® and Tungsten Carbide. Segments
adjustable based on wear.
U.S. Gallons
Per Minute (GPM)
3000
2800
2600
2400
2656 GPM Max
2200
2000
si
25 p
1800
1600
1400
1450 GPM
1200
1000
0
1000
1100
1200
1300
1400
1500
1600
1700
1800
1900
2000
Engine Speed (RPM)
The above curve is based on pumping clear water at 62 degrees
with no lift required and no restrictions in the discharge.
SOUND ENCLOSURE SPECIFICATIONS
Sound Level: Holland Pump Supersilent pump units are tested for Sound
Level using the Contractors Pump Bureau Sound Level Measurement
Standard for Pump Units using a calibrated Sound Level Meter. This
procedure produces an average Sound Level based on eight measurements
under strict conditions of pump placement. They are tested at full RPM
pumping water. The sound Level result for the WP12-SS is 57 dBA @ 23 feet.
Enclosure: Aluminum construction, removable for ease of maintenance.
Stainless steel accessories including bolt on, lift off hinges.
GEAR SPECIFICATION
PTO Gear Reduction: 3.66 to 1
ENGINE SPECIFICATIONS
Skid Base
Net Weight (lbs)
6300
Shipping Weight (lbs)
6450
Export Crate Size (cu. ft) 285
Model: John Deere 4045TI530, Tier 4 Final Or Approved Alternate
Type: 4 Cylinder, 4 Stroke, Turbocharged, DOC, Liquid Cooled Diesel Engine
Displacement: 3.6L (220cu.in.)
Governor: Electronic
Lubrication: Forced Circulation
Air Cleaner: Dry Type with Replaceable Element
Lube Oil Capacity: 2.9 U.S. Gallons (9L)
Coolant Capacity: 3.4 U.S. Gallons (13L)
Fuel Tank: Integral 143 U.S. Gallon Capacity (#2 Diesel Fuel)
Full Load Operating Time: 60 Hours Minimum @ 2000 PSI
Starter: 12 Volt, 2.0 kW
Standard Features: Skid, SAE Flywheel Housing, SAE Flywheel, SAE B
Pump Adaptor
Control Panel: Controls Inc. (CD-83504-AS or Equal): Engine Temperature
and Low Oil Pressure with optional Gauge, Key Start, and Hour Meter,
optional add-on Cornell (Co-Pilot): Location, Engine Controller Data,
Temperature, Vibration, Flow, Pressure, Oil Level, Run-time, RPM, Amps
Optional Features: Site or DOT Highway Trailer
John Deere Published Performance: Maximum Continuous Power: 67HP
(50kW) @ 1800 RPM
Holland Pump Administration Office 2005 Vista Pkwy., West Palm Beach, FL 33411
T (561) 697-3333 E info@hollandpump.com
